Password Recovery Procedures for some Cisco appliances. The following link is about the index of password recovery procedures for some Cisco appliances. Next discussion is for others such as IronPort and Nexus switch Password Recovery. Note: For security reasons, the password recovery procedures. During for instance password recovery there is a need to send a break to the router. In putty (tested with both Windows and Linux) this is done by pressing ctrl+break.

I purchased a 1700 series router off ebay, but it's been setup with tacacs authentication. So i just get the username password situation when i try to login. I have asked the seller for a password to use, but seller wasn't the old user and does not know. So i believe i need to restart the router, issue the break command and i'll be put into rommon mode where i can by pass the start-up config file and get onto the router and create a new config file.

How To Install A Microsoft Dynamics Ax Hotfix Kb947821. So simple in theory. I'm having trouble issuing the break command.

I am using teraterm and have restarted the router and then clicked alt - b every few seconds for a minute but the router just boots as normal. I went to control and ->send break. But still the same. Router just boots as normal. I've tried ctrl-b, alt-ctrl-b.

I tried it using putty. Still nothing works. I have tried holding down the space bar for 15 seconds after power on. This put the router into some kind of mode.

It looked hopefully, but neither putty or terterm would connect to the router after this. The yellow ok light kept flashing like it does when the IOS is loading. Any ideas for me?? Are you using a USB->Serial adapter or an actual old school serial port? Some USB->Serial adapters had issues with sending the break sequence. If that's the case, either try a different USB->Serial adapter or find a computer (or old laptop) with a built in serial port. You could always try different terminal software.

I think ctrl-break worked for me in the old free hyperterminal -- but I always had a good working USB->Serial adapter or laptop with a normal serial port. Another possibility is that the no service password-recovery command was issued. But you can still get into the router, you just lose the existing configuration. The CTRL-Break sequence (rather than just the break sequence) should work for that -- but you should see the message when you boot ().

So I'm going with bad USB->Serial Adapter. Final Answer. I purchased a 1700 series router off ebay, but it's been setup with tacacs authentication. So i just get the username password situation when i try to login.

I have asked the seller for a password to use, but seller wasn't the old user and does not know. So i believe i need to restart the router, issue the break command and i'll be put into rommon mode where i can by pass the start-up config file and get onto the router and create a new config file. So simple in theory. I'm having trouble issuing the break command. I am using teraterm and have restarted the router and then clicked alt - b every few seconds for a minute but the router just boots as normal. I went to control and ->send break. But still the same.

Router just boots as normal. I've tried ctrl-b, alt-ctrl-b. I tried it using putty.

Still nothing works. I have tried holding down the space bar for 15 seconds after power on. This put the router into some kind of mode.

It looked hopefully, but neither putty or terterm would connect to the router after this. The yellow ok light kept flashing like it does when the IOS is loading. Any ideas for me??In TeraTerm the break is ALT+B. Maybe the last person who used the router disabled the break.

If I remember it right it has something to do with the config registry value. TechExams.Net is not sponsored by, endorsed by or affiliated with Cisco Systems, Inc. Cisco®, Cisco Systems®, CCDA™, CCNA™, CCDP™, CCNP™, CCIE™, CCSI™; the Cisco Systems logo and the CCIE logo are trademarks or registered trademarks of Cisco Systems, Inc. In the United States and certain other countries. All other trademarks, including those of Microsoft, CompTIA, Juniper ISC(2), and CWNP are trademarks of their respective owners. Powered by vBulletin® Version 4 Copyright ©2000 - 2018, Jelsoft Enterprises Ltd. Search Engine Optimization by 3.6.0.

This document provides standard break key sequence combinations for the most common operating systems, and some tips on how to troubleshoot problems. The RS-232 logic level uses +3 to +25 volts to signify a Space (Logic 0) and -3 to -25 volts for a Mark (logic 1).

A break signal is when the data line remains in the space condition for a specified duration, usually 100 ms to ½ second. All characters begin with a start bit and end with a stop bit (and also a parity bit or two). Reign Of Fire Ost Rar Download. The level condition of the start and stop bits is always opposite. So, no character combination can look like the break signal.